How To Clean Water Inlet Valve On Dishwasher

Download Article

The water inlet valve feeds the water from your home's water line into the dishwasher. When this valve is defective, water can leak out of your dishwasher. If it doesn't let enough water in, your dishes may not be cleaned correctly! Fixing the dishwasher's inlet valve is an easy project for the DIY'er.

Steps

1

Shut off the water and power to the dishwasher before starting. Remove the two quarter-inch hex screws located on the bottom of the dishwasher's front cover.
2
Remove the screws under the dishwasher door. Tip the front cover outward and the bottom panel should come out. Remove this panel.
- Remember where all four of the screws were located. The longer ones belong to the bottom of the front cover. Trying to place the long screws into the upper part could puncture the plastic basin, resulting in leaks.
3

Find the inlet valve. In most makes and models, it is located at the bottom of the machine.
4

Detach the water hose from the valve and remove the fitting that attaches the valve to the dishwasher.
5

Remove the valve. Keep the fitting, as it can be reused!
6

Locate and remove the two quarter-inch screws. These screws fasten the bracket of the inlet valve to the side of the dishwasher.
7

Angle the inlet valve downward to remove the electrical harness that is attached to the valve's solenoid assembly.
8
Using a pair of needle-nose pliers, squeeze the spring clamp fastening the outlet hose to loosen it and move it up. This will enable the hose to be jiggled free of the valve.
- Have a sponge, rag or towel ready as leftover water can run out of this hose.
9

Pull the old valve out and discard it. Install the new one and fasten it using the old fitting.
10

Remove any old plumbing tape and clean the fitting with a stiff wire brush. Apply a new length of Teflon tape, taking care not to get any of it inside the fitting.
11
Using a vise-grip plier, tighten the fitting before it is placed back inside of the dishwasher.
- If you don't have vise-grip plier the fitting will have to be threaded manually onto the inlet valve as much as possible. Once it is on a solid surface, it can be fully tightened.
12

Place the spring clamp back onto the outlet hose and reattach the hose to the inlet valve. Use a jiggling motion to get the hose back onto the valve to ensure that it is seated as firmly as possible.
13

Using the needle-nose pliers, squeeze the spring clamp once again and wiggle it back down the outlet hose. This keeps the outlet hose properly sealed and prevents any leakage.
14

Reattach the new valve to the side of the machine with the two quarter-inch screws that were used to mount the old inlet valve.
15

Reattach the valve's water supply hose and carefully connect the electrical harness to the inlet valve solenoid. Make sure the inlet valve fitting is good and tight at this time.
16

Turn on the electricity and the water supply to the dishwasher and start it up. Watch closely for any leaks from the outlet hose or the inlet valve itself. If there are no apparent leaks, reinstall the front panels onto the dishwasher by reversing the process in the first step of these instructions. Take special care to insert the screws into their proper holes.

Add New Question

Question

What are some common causes for a dishwater to start leaking?

Gevorg Grigorian is an Appliance Repair Specialist and the Owner of G and R Appliance Repair in Los Angeles, California. With over 13 years of experience, Gevorg specializes in residential and commercial appliance repairs as well as heating, ventilation, and air conditioning (HVAC) services. Gevorg holds a BS in Business Administration and Management from California State University-Northridge.

Appliance Repair Expert

Expert Answer

Support wikiHow by unlocking this expert answer.

There are a few reasons why dishwashers will leak. Most commonly, they tend to leak from the left or right side of the door or even simultaneously on both sides due to a worn out gasket. Another reason may be that the rubber tubing and hoses of the dishwasher have been punctured by a piece of glass or even rodents chewing the tubing.

Ask a Question

200 characters left

Include your email address to get a message when this question is answered.

Submit

Video

Use a magnet or magnetic parts tray to prevent the screws from being lost.

Disconnect the water supply to the dishwasher and turn off the electricity before doing any work on it.

Things You'll Need

¼ inch nut driver
Needle-nose pliers
Vise-grip pliers
Adjustable wrench
Teflon plumber's tape
Small wire brush

References

About This Article

Thanks to all authors for creating a page that has been read 36,533 times.

Did this article help you?

Get all the best how-tos!

You're all set!